Next Article in Journal
Prospects and Challenges of Translational Corneal Bioprinting
Next Article in Special Issue
Influence of Liquid-to-Gas Ratio on the Syngas Fermentation Efficiency: An Experimental Approach
Previous Article in Journal
Culture Time Needed to Scale up Infrapatellar Fat Pad Derived Stem Cells for Cartilage Regeneration: A Systematic Review
Previous Article in Special Issue
Flax Biomass Conversion via Controlled Oxidation: Facile Tuning of Physicochemical Properties
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Techno-Economic Assessment of Bio-Syngas Production for Methanol Synthesis: A Focus on the Water–Gas Shift and Carbon Capture Sections

ENEA–Italian Agency for New Technologies, Energy and Sustainable Economic Development, Department of Energetic Technologies, Trisaia Research Centre, I-75026 Rotondella, Italy
*
Author to whom correspondence should be addressed.
Bioengineering 2020, 7(3), 70; https://doi.org/10.3390/bioengineering7030070
Submission received: 1 June 2020 / Revised: 1 July 2020 / Accepted: 2 July 2020 / Published: 4 July 2020
(This article belongs to the Special Issue Biomass Conversion)

Abstract

:
The biomass-to-methanol process may play an important role in introducing renewables in the industry chain for chemical and fuel production. Gasification is a thermochemical process to produce syngas from biomass, but additional steps are requested to obtain a syngas composition suitable for methanol synthesis. The aim of this work is to perform a computer-aided process simulation to produce methanol starting from a syngas produced by oxygen–steam biomass gasification, whose details are reported in the literature. Syngas from biomass gasification was compressed to 80 bar, which may be considered an optimal pressure for methanol synthesis. The simulation was mainly focused on the water–gas shift/carbon capture sections requested to obtain a syngas with a (H2CO2)/(CO + CO2) molar ratio of about 2, which is optimal for methanol synthesis. Both capital and operating costs were calculated as a function of the CO conversion in the water–gas shift (WGS) step and CO2 absorption level in the carbon capture (CC) unit (by Selexol® process). The obtained results show the optimal CO conversion is 40% with CO2 capture from the syngas equal to 95%. The effect of the WGS conversion level on methanol production cost was also assessed. For the optimal case, a methanol production cost equal to 0.540 €/kg was calculated.

Graphical Abstract

1. Introduction

Gasification is a thermochemical process for the conversion of a solid organic material, typically coal or biomass, into syngas. From a chemical point of view, gasification occurs due to the partial oxidation of a solid material at temperatures of 700–900 °C by means of a gasifying-oxidant agent, such as air, oxygen, steam or carbon dioxide. Gasification involves three main steps, namely, (i) solid drying; (ii) solid pyrolysis with formation of gases, volatile compounds and char; and (iii) secondary reactions, which convert the pyrolysis gas to syngas. Globally, gasification is an endothermic process; therefore, the system requires an energy input. The produced syngas is a mixture of incondensable gas at room temperature and atmospheric pressure that usually are carbon monoxide, hydrogen, carbon dioxide, methane and light hydrocarbons. In the case air is used as the gasifying agent, nitrogen is also present. Syngas from biomass has gathered huge attention in the last decades because it can be considered as a renewable source of energy, as the carbon dioxide released from syngas utilization is balanced by the carbon dioxide sequestration by plants during photosynthesis. For decades syngas has been proposed as fuel for cooking, lighting or for car engines. More recently, it has been used for combined heat and power production in internal combustion engines (ICEs). For this application, air is usually used as the gasifying agent due to its low cost. A syngas with a heating value of 4–5 MJ/Nm3dry is usually obtained, which must be carefully cleaned of particulates and tar below 0.05 g/Nm3 and 0.1 g/Nm3, respectively, before being used in an engine [1]. Worldwide, extensive expertise has been acquired with a gasifier coupled with an ICE with power from tens of kWe to a few MWe [2,3,4,5]. Beyond the power production, the production of strategic green chemicals (e.g., methane, methanol and DME) from syngas is attracting the attention of the scientific community because it reduces the greenhouse gas emission and it partially preserves the chemical energy of syngas.
In particular, biomass gasification may be a sustainable way to produce methanol, which may be considered a strategy to introduce green energy in the industrial chain for chemicals and fuels. In fact, methanol is considered one of the most valuable green energy carriers of the future, since it may replace fossil sources (e.g., coal, natural gas or crude oil) for producing chemicals and fuels, [6,7,8]. Currently, several industrial plants produce dimethyl ether, olefins or gasoline starting from methanol [9,10,11,12]. Methanol is actually produced from syngas, usually obtained by means of steam reforming of natural gas. The syngas-to-methanol reaction is conventionally performed in a fixed-bed tubular reactor operating at 60–100 bar and 250–280 °C over a Cu–ZnO-based catalyst. In order to use conventional technologies, biomass-derived syngas needs to be treated and upgraded to obtain a syngas with the proper characteristics for methanol synthesis. For instance, tar removal is of paramount importance to prevent the catalyst’s deactivation. Both chemical and thermal techniques may be used for tar removal, although catalytic conversion seems to be the most effective way to reduce the tar content and convert them into syngas or light hydrocarbons [13,14]. An important aspect to consider is the (H2CO2)/(CO + CO2) ratio. In fact, with conventional technologies for methanol synthesis, the optimal (H2CO2)/(CO + CO2) molar ratio should be equal to 2 [15].
Unfortunately, syngas is far from having the above-written ratio, mainly because of elemental composition of the biomass is quite deficient in hydrogen compared to carbon. Hydrogen is only 6–7 wt% while carbon is about 47–49 wt% of the dry, ash-free biomass. This drawback could be theoretically overcome by a proper choice of the gasifying agent and reactor design. For instance, the utilization of steam as a gasifying agent improves hydrogen yield by means the three following reactions:
C + H 2 O = C O + H 2                     Δ H ° ( 298   K ) = 131 kJ mol
C H 4 + H 2 O = 3 H 2 + C O           Δ H ° ( 298   K ) = 206 kJ moll
C O + H 2 O = C O 2 + H 2             Δ H ° ( 298   K ) = 41 kJ mol
The reactants of Reactions (1)–(3), namely C, CH4 and CO, are during the biomass pyrolysis step. The involved reactions, as well as the Boudouard reaction, methanation, drying and pyrolysis, are globally endothermic; therefore, heat supply is necessary to sustain the gasification process at 800–900 °C. For instance, the reactor may be heated by an external thermal source. In this case, the performances of the heat exchange and the global efficiency of the process should be considered.
McCaffrey et al. performed gasification tests of almond shells on a bench scale, electrically heated, bubbling fluidized bed gasifier by using steam as the gasifying agent. They detected interesting results in terms of the syngas composition: 35–40 vol% hydrogen, 18–21 vol% carbon monoxide, 16–18 vol% carbon dioxide, 17–21 vol% nitrogen and 5–6 vol% methane [16]. Nevertheless, with the goal for scaling-up the process from a bench to industrial scale, the heat supply for the endothermic gasification reactions should be provided in a simpler and efficient way. In this regard, the injection inside of the reactor of an oxidant agent, such as air or oxygen, is a prosecutable way. In fact, Campoy et al. gasified biomass by means of an air–steam mixture in a fluidized bed gasifier under simulated autothermal and adiabatic conditions, with the aim of reproducing the behavior of a full-scale fluidized bed gasifier [17]. They detected a syngas with the following composition: 12–16 vol% hydrogen, 12–15 vol% carbon monoxide, 16–19 vol% carbon dioxide, about 5 vol% methane and about 50 vol% nitrogen. They also showed that a proper selection of operating conditions makes it possible to increase the gasification efficiency from 40% to 60%. On the other hand, the main drawback of the air–steam gasification is related to the large dilution in nitrogen, with all the negative consequences on the thermodynamic and kinetics of the methanol synthesis, which is favored at high partial pressures of the reactants. Therefore, the utilization of pure oxygen instead of air has undoubted advantages concerning the production of a syngas for methanol synthesis. On the other hand, an additional cost is associated with pure oxygen production, although it may have some advantages in terms of capital investment costs linked to the reduced size of the reactor and related equipment because of the reduced volumetric flows. Studies on the relatively low-cost technology for oxygen production strengthen the feasibility of syngas production from oxygen–steam gasification [18,19]. Meng et al. gasified different biomass in a 100 kWth steam–oxygen-blown circulating fluidized bed gasifier (CFB). They observed that the product gas composition obtained from willow over the temperature range from 800 to 820 °C consisted of a syngas with a high H2 concentration (29 vol%), and with CO (22 vol%), CO2 (38 vol%), CH4 (7 vol%) and C2-C3 (3 vol%) [20]. Barisano et al. gasified almond shells in a 1 MWth pilot plant based on a bubbling fluidized bed gasifier with internal recirculation by using a mixture of enriched air–steam and oxygen–steam. Obviously, the best results in term of syngas composition for methanol production were obtained in the case of pure oxygen–steam gasification at process temperatures of 820–830 °C, with 30–33 vol% hydrogen, 28–32 vol% carbon monoxide, 22–27 vol% carbon dioxide, 9–11 vol% methane, 1–2 light hydrocarbons and 2–5 vol% nitrogen [21]. An alternative way for supplying thermal energy for endothermic steam gasification was developed at TUW: it consists of the utilization of the bed material as a heat carrier in a dual fluidized bed. The obtained syngas showed the following composition: H2 (36–42 vol%), with CO (19–24 vol%), CO2 (20–25 vol%), CH4 (9–12 vol%) and C2-C3 (3–4 vol%) [22]. From this short review about biomass steam gasification, it can be argued that, despite of these efforts, the syngas’s (H2CO2)/(CO + CO2) ratio is still far from 2; therefore, additional steps need to be implemented in order to both increase the H2 content and reduce the CO2 level, although several efforts have been done in last decades aimed to develop catalysts for CO2-rich syngas conversion towards methanol or methanol-derivates [23,24,25,26,27]. Feng et al. analyzed the production of methanol from biomass gasification by simulating a plant mainly consisting of a biomass gasifier, steam reformer and methanol synthesis reactor [28]. The authors adopted a pressure swing adsorption (PSA) unit to separate hydrogen from the unreacted gases and recycling it to the reactor inlet. With this approach, the (H2CO2)/(CO + CO2) molar ratio in the methanol reactor inlet was increased up to 0.7, which is still far lower than the ideal value. PSA was also adopted in the study of Puig-Gamero in order to adjust the composition of syngas coming from a gasification unit [29].
A water–gas shift reaction (WGS, CO + H2O = CO2 + H2) represents the most used method to increase the hydrogen content in syngas. WGS is normally used after steam reforming or partial oxidation of natural gas or coal to produce hydrogen-rich syngas. The WGS is an exothermic reversible reaction. Due to the thermodynamics constraint, WGS is normally performed in two separated reactors: a high temperature shift reactor (HTS) and a low temperature shift reactor (LTS). Following this approach, in the first reactor kinetics is favored due to the high temperature, while thermodynamics is favored in the low temperature reactor, allowing obtaining high H2 yield. HTS is normally performed up between 310 °C and 450 °C and 25–35 bar by using an iron/chromium catalytic system, where iron acts as active sites while the presence of chromium reduces the iron sintering [30]. The LTS step is usually carried out between 200 °C and 240 °C with a copper/zinc/alumina catalytic system able to convert the residual CO in the case pure hydrogen is desired. In order to obtain a syngas with a composition suitable for methanol synthesis, the WGS section needs to be integrated with a CO2 removal section. In this regard, absorption is the most used technology to remove CO2 from syngas streams. Ju et al. adopted a WGS downstream of the biomass gasification unit in order to increase the hydrogen content. In the WGS unit, the CO conversion was set at 70%, and the CO2 was removed by the Rectisol process [31]. Robinson et al. used the WGS coupled with Selexol, in order to produce pure hydrogen from syngas derived from a gasification unit. The obtained hydrogen-rich gas was mixed with the raw syngas to obtain a suitable composition for methanol synthesis. In this study, CO was almost totally converted in the WGS step, and about 90% of the CO2 was removed in the Selexol unit [32]. The aim of this work is to study in more detail, in terms of economic analysis, the WGS and carbon capture section (CCS). In particular, capital costs and operating costs were assessed as a function of the WGS conversion level, taking as the target a syngas suitable for methanol synthesis. An optimal WGS conversion/CCS configuration is suggested on the basis of the obtained results.

2. Materials and Methods

2.1. R-Ratio and WGS Conversion/Carbon Capture Relationship

As discussed in the introduction, the syngas produced by biomass gasification needs to be upgraded in order to obtain a (H2CO2)/(CO + CO2) molar ratio (here named R-ratio) equal to 2, optimal for methanol synthesis [33]. The following strategies can be used to adjust the R-ratio to the desired value:
(A)
add pure H2 [34];
(B)
remove CO2 [32].
The A strategy has an impact on the numerator of the R-ratio, and it is possible to obtain an R-ratio = 2 by adding a large quantity of pure hydrogen, as may be observed from the following equation:
H 2 , I N C O 2 , I N C O I N + C O 2 , I N H 2 , I n + H 2 , P U R E C O 2 , I N C O I N + C O 2 , I N
where H2,IN is the inlet hydrogen molar flowrate, CO2,IN is the inlet carbon dioxide molar flowrate, COIN is the inlet carbon monoxide molar flowrate, and H2,PURE is the inlet pure hydrogen molar flowrate. The main hurdle of this strategy is related to the production of pure hydrogen in a sustainable way. In fact, traditional processes for hydrogen production are based on fossil sources (e.g., coal, oil and natural gas) with a high CO2 emission, even though at a relatively low cost [35]. On the contrary, renewable electricity sources (e.g., wind) may be used to produce hydrogen with a low carbon footprint via water electrolysis [34]. Actually, the addition of pure hydrogen is clearly an expensive strategy, even though water electrolysis with atmospheric carbon dioxide capture is an attractive route to produce methanol [36].
The B strategy can be applied by means of different process schemes. In particular, CO2 removal can be simple or difficult (cheap or expensive), depending on whether the CO2 molar fraction (and partial pressure) is low or high, respectively [37].
The CO2 removal from clean syngas can be useless if the molar fraction of H2 and CO are not appropriate for methanol synthesis. For example, depending on the syngas quality, a 100% CO2 capture may produce an R-ratio (H2/CO) lower than 2, and thus not suitable for methanol synthesis.
On the other hand, if the CO2 molar fraction is too low, it is very difficult to achieve high CO2 capture in order to obtain an optimal R-ratio [38]. Therefore, the viability of the carbon capture section strongly depends on the syngas composition.
As mentioned in the introduction part, CO may be partially converted to hydrogen by the water–gas shift reaction, which would lead to an increase in both hydrogen and CO2 content. Nevertheless, by WGS only it is not possible to change the R-value, as perhaps easily demonstrated:
H 2 , I n C O 2 , I N C O I N + C O 2 , I N H 2 , I n + C O I N x W G S ( C O 2 , I N + C O I N x W G S ) C O I N C O I N x W G S + C O 2 , I N + C O I N x W G S = H 2 , I n C O 2 , I N C O I N + C O 2 , I N  
where xWGS is the CO conversion in the WGS section. Nevertheless, in this way, the H2 molar ratio increases as well as the CO2 molar ratio, making the CO2 removal simpler [39]. In this study, we used a syngas with a composition as reported in the paper of Barisano et al. [21]. Briefly, the authors reported a study about gasification of almond shells with a 1000 kWh pilot-scale, internally circulating, bubbling fluidized bed reactor, by using a steam/O2 mixture as the gasification agent. Both char and tar were abated with a ceramic filter and wet scrubber, respectively. The gas stream from the gasification unit is assumed to be cleaned from residual tars and sulfur compounds, obtaining a mixture with the average composition reported in Table 1.
As may be noted, CO2 removal is useless without a WGS step, due to the relatively low hydrogen content in the syngas. In particular, the minimum WGS conversion (corresponding to a 100% CO2 capture rate) is equal to about 33%, obtaining an R = 2:
H 2 , I N + C O I N x W G S ( C O 2 , I N + C O I N x W G S ) ( 1 1 ) C O I N C O I N x W G S + ( C O 2 , I N + C O I N x W G S ) ( 1 1 ) = 2   30 + 30 x W G S 30 30 x W G S = 2   x W G S = 0.33  
Similarly, it is possible to individuate the minimum CO2 capture rate (corresponding to a 100% WGS conversion) equal to 64%:
H 2 , I N + C O I N ( C O 2 , I N + C O I N ) ( 1 α C O 2 ) C O I N C O I N + ( C O 2 , I N + C O I N ) ( 1 α C O 2 ) = 2   60 ( 55 ) ( 1 α C O 2 ) ( 55 ) ( 1 α C O 2 ) = 2   α C O 2 = 0.64
Furthermore, the CO2 capture rate (αCO2) as a function of WGS conversion xWGS may be calculated as follows:
α C O 2 = 2   C O I N H 2 I N + 3   C O 2 , I N 3   ( C O 2 , I N + C O I N   x W G S )
Figure 1 shows that αCO2 decreases with the WGS conversion.

2.2. Flowsheet Description

Figure 2 shows the process flowsheet (drawn using Microsoft Power Point software) considered in this work based on two consolidate technologies: two-step WGS and CO2 absorption by the Selexol® process.
After the syngas purification process, the syngas is compressed (C1) at the methanol synthesis pressure (here 80 bar). The heat exchanger E1 heats the compressed syngas for the HTS-WGS at 400 °C. Water is vaporized and superheated to 400 °C by E2. As mentioned in the introduction part, in the HTS-WGS reactor, Fe2O4/Cr2O3 is usually used as the catalyst [40]. WGS is an exothermic reaction, so in the adiabatic reactor the increase in temperature causes a decrease in the reaction equilibrium conversion [41]. Moreover, the higher the inlet temperature is, the lower will be the equilibrium conversion. So, if a high CO conversion is requested, LTS-WGS may be considered as well, in order to promote a reaction from a thermodynamics point of view. Catalysts used for this step is Cu–ZnO–Al2O3 and the temperature is set to 200 °C [42]. The heat exchanger E4 allows for the condensation of the residual water, which is recycled back to E2. H2/CO2-rich gas is then sent to a small compressor to reestablish the pressure at 80 bar due to the pressure drop in the WGS reactors. The absorption column ABS works at 30 °C in order to promote the absorption of CO2 in the solvent. Liquid outlet stream from the bottom of the column (rich in CO2) is expanded in order to recover the other volatile compounds (H2 and CO). A flash (F2) at 30 °C recycles these gases to the column. The DEPG solvent and CO2 are then expanded again by the V2 valve and the F3 flash allows the recovery of high pure CO2 (higher than 99% of purity) and regeneration of the solvent. Pure CO2 is finally compressed until 110 bar for the storage [43]. Regenerated DEPG is compressed again by the P2 pump and recycled. A gaseous H2-rich stream from the top of the ABS is compressed, if necessary, and heated to 200 °C, to be recycled to the methanol synthesis reactor.
A detailed list of the main items considered in this work with the type of auxiliary stream is reported in Table 2.
The main equipment in terms of utility consumption is further detailed here:
-
C1 is the main compressor of the process, because the clean biomass-derived syngas is considered at 1 bar.
-
E2 is the main heat exchanger of the process, because it vaporizes water at high pressure (80 bar); at this pressure the vaporization temperature of water is about 295 °C, so a boiler (fueled with natural gas) is necessary for both vaporization and superheating. Hence, the H2O/CO ratio for the WGS sets the thermal power (and the natural gas demand) of E2.
-
C3 is the compressor of the gaseous stream recycled to the ABS column and the electricity required depends on the pressure drop at the throttling valve necessary to release volatile compounds (H2 and CO), leaving CO2 into the solvent.
-
C5 is considered to compress CO2 at 110 bar for storage [43].
-
P2 is an energy-intensive pump, as a large amount of DEPG solvent is requested to make the CO2 capture possible.
Considering the general flowsheet of Figure 2, several process parameters can be modified in order to obtain different xWGS and αCO2 and, consequently, an R-ratio equal to 2. The L/D ratio of the WGS reactors was set equal to 8.
Furthermore, Table 3 shows the process variables investigated in this work and their effect on the process.
One of the main process variables to increase the CO conversion in the WGS unit is the H2O/CO ratio. The WGS reaction is limited by thermodynamics, therefore theoretical conversion of CO may be increased by increasing the H2O/CO ratio. To have a good reactor set up, a minimum H2O/CO ratio of 1 is necessary. With the increase in the H2O/CO ratio, a higher CO conversion can be obtained, but the heating power of E2 can become too high to justify higher conversions. In order to limit the pressure drop, parallel adiabatic tubular reactors with the same length and diameter were considered. So, a higher number of tubes must be used in order to save electricity at C2.
With the increase in the number of tubes, a higher volume is obtained and, consequently, a higher conversion, with an acceptable pressure drop (less than 2 bar) [44].
For the carbon capture section, both the DEPG/GAS ratio and expansion pressure of V1 and V2 have to be set in order to have an R-ratio equal to 2, and low values of solvent quantity and electricity of the P2, C3 and C5 items
In particular, a higher DEPG/GAS ratio correspond to a higher absorbed quantity of CO2, H2 and CO. Consequently, lower V1 pressures may be set to recover H2 and CO, and therefore a higher electricity demand for both the C3 and P2 items were calculated. A lower DEPG/GAS ratio correspond to a lower absorbed quantity of CO2, H2 and CO, which may be insufficient for obtaining the αCO2 required for the correspondent xWGS, and the V2 pressures have to be then set to a lower value in order to completely regenerate the solvent, then requiring a higher C5 electricity demand.

2.3. Process Simulation Description

A clean syngas with a composition as in Table 1 was fed to the process simulation scheme as reported in Figure 2. Pumps and compressors were considered adiabatic devices with an efficiency equal to 0.85 and 0.75, respectively. Hot streams with a temperature in the range 100–500 °C were coupled with cold streams with a temperature in the range 0–200 °C, for heat integration purposes. Cold streams at temperatures higher than 200 °C were considered supplied by a boiler fueled with natural gas.
HTS-WGS kinetics from Hla et al. (2009) [40] and LTS-WGS kinetics from Choi et al. (2003) [42] were adopted for the simulation. Both the WGS reactors were considered adiabatic and pressure drop was calculated by the Ergun relationship [43]. Thermodynamic models used for the simulation were the NRTL model for the estimation of activity coefficients for the liquid phase and the Soave–Redlich–Kwong equation for the gas phase [45]. An equilibrium absorption column was used for ABS.
In order to fix the xWGS-αCO2 working points, a sensitivity analysis was carried out by varying the process variables reported in Table 3. Considering also the impact of the process variables on the process economics, from the sensitivity analysis were selected the WGS reactor sizes with the lowest lengths (and the lowest pressure drops), the lowest H2O/CO ratio, the lowest DEPG/GAS ratio and the maximum V1 and V2 pressures.

2.4. Economic Assessment Description

For the economic assessment of the whole process, both CAPEX and OPEX costs were evaluated.
In particular, the biomass supply chain and pure oxygen costs, natural gas cost, electricity cost, maintenance and labor costs were considered as the operating costs (OPEX). The economic data used in the analysis are reported in Table 4. A biomass supply chain cost equal to 40 €/t was considered from Menin et al. (2020) [46] for a plant size equal to 147,000 t/y (18.6 t/h) of biomass fed to the gasifier, producing 861 kmol/h of syngas. Maintenance and labor costs were associated to the capital costs and estimated as 10% of the annual total capital costs.
The capital costs considered were the following:
-
Gasifier + gas cleaning system [52].
-
All pumps and compressors for the WGS and CC sections [49].
-
WGS reactors, considering shell and catalysts separately [49].
-
ABS column, considering shell and packing separately [49].
For all the equipment, both the scale economies, temperature and pressure ranges were considered as follows:
C C j = C C 0 , j ( Q j Q 0 , j ) m j F i F t F p
where CCj is the capital cost of the j-equipment, CC0,j is the capital cost of the j-equipment for the size Q0,j, Q0,j is the base size for the j-equipment, and Ft and Fp are the temperature level factor and the pressure level factor, respectively. Fi is the installation factor reported in the references where cost data are reported [49,52].
A 4-year catalyst charge was set in the cash flow analysis in order to calculate the production cost of the methanol, and the global methanol yield from the syngas with an R-ratio = 2 was set to 80% [53]. The capital costs for the methanol synthesis unit were taken from Reference [54].
The NPV (net present value) was set equal to 0, and the corresponding value of the selling price of the produced methanol was then calculated as follows:
N P V = i = 0 n C F i ( 1 + r ) i = 0
C F i = ( P M e O H F M e O H , i O C i ) ( 1 t ) + W C i + C C T O T y D t C C i
where CFi are the cash flow of the year i, r is the discount rate, n is the final year (22), PMeOH is the production price of syngas-to-methanol, FMeOH,i is the molar flowrate of methanol for the year i, OCi are the operating costs for the year i, t is the tax ratio, WCi is the working capital, CCTOT are the total capital costs, and yD are the depreciation years.
The working capital was set as a negative value at the start-up year (i = 2), and as a positive value at the last year (i = 21). The construction of the plant was considered completed between years 0 and 1 (equal capita cost each year).

3. Results

3.1. Process Results

Table 5 shows the process simulation results in terms of the process variables values obtained from the simulation, sensitivity, economic analysis and variable optimization.
In particular, the minimum CO conversion in the WGS step was set to 36%, while the maximum one to 99%. By varying the HTS-WGS reactor length, the WGS conversion equaled 36%, or 40%, and the H2O/CO equaled 1; a one-step WGS was sufficient to reach the conversion desired. Furthermore, for the WGS conversion of 49% and 59%, only HTS was sufficient, but a H2O/CO equal to 2 was required, because the addition of the LTS reactor is not sufficient to reach the desired conversions.
By increasing the CO conversion from 36% to 59%, which correspond to a CO2 capture rate decrease from 98% to 82%, respectively, the DEPG/CAS molar ratio may be decreased from 1 to 0.7. V1 pressure varies between 19 and 25 bar; furthermore, the V pressure decreases as the αCO2 value decreases. When the CO2 partial pressure in the syngas-fed inlet to the column is higher, the CO2 capture is favored, but the required αCO2 is lower. Consequently, a higher flowrate of the gas recycled to the column is calculated, and a lower V1 pressure needs to be set. The optimal pressure of the V2 valve increases as the CO2 capture decreases, because a lower regeneration level of the solvent is requested, also in relationship with the DEPG/GAS ratio.
A H2O/CO molar ratio equal to 2 was sufficient for a CO conversion in the WGS equal to 70% and 80%, while the H2O/CO molar ratio has to be increased to 3 for a conversion higher than 90%. In these cases, the LTS-WGS unit is necessary from a thermodynamics point of view, and then 70%, 80%, 90% and 99% xWGS may be obtained. The CO conversion reaction rate is slower in the LTS-WGS due to a lower reactant concentration and reaction temperature with respect to the HTS-WGS step.
In order to obtain a CO2 capture rate of 76%, 72%, 67% and 64% after the WGS units, which correspond to 70%, 80%, 90% and 99% of the CO conversion, respectively, a DEPG/GAS ratio was set equal to 0.5. A maximum V1 pressure of 58 bar (minimum compressor power demand of C3 compressor) was found for a CO conversion of 70%. This high pressure is due to the high concentration of CO2 in this stream. To obtain the regeneration of the solvent, the lowest value of the V2 pressure was necessary (0.7 bar). The decrease in the αCO2 values cause a decrease in V1 pressure in order to recover a small quantity of CO2 solubilized in the column outlet stream for these cases.
Figure 3 shows both the thermal and the electricity power demand as a function of CO conversion in the WGS steps. In particular, the natural gas demand obviously increases by increasing the H2O/CO ratio for the WGS reactor due to the higher production of steam. For an xWGS equal to 36% and 40%, which requires a H2O/CO ratio equal to 1, about 2.7 MWt of thermal energy is calculated. About a double value was calculated for a CO conversion in the range of 49–80%, which were obtained with a H2O/CO ratio equal to 2. A slighter effect of CO conversion on electricity power demand was calculated, as it varies between 8.6 and 9.3 MWe. A more careful analysis reveals that the minimum value was achieved at a 90% CO conversion. Electrical demand is mainly related to the DEPG recycle pump (P2) and CO2 compressor (C5) units. Both the power demands increase as the CO conversion decreases. For xWGS = 99%, the recovery compressor C3’s power is higher than xWGS = 70%, 80% and 90%, due to the lower V1 pressure.
Figure 4 reports the characteristics of the upgraded syngas in terms of CO2 content and LHV. CO2 content increases by increasing the CO conversion, increasing from about 1% to about 21% by increasing the CO conversion from 36% to 99%, while the CO2 removal decreases from 98% to 64%. The CO2 molar fraction obviously has an impact on the lower heating value of the upgraded syngas that decreases from about 25 MJ/kg to about 18 MJ/kg, by increasing the CO2 content from 1% to 21%.
Methanol synthesis occurs by hydrogenation of the CO and CO2 compounds, so in the stream syngas-to-methanol, only CO and CO2 can be converted to methanol. The carbon loss due to the WGS/CCS unit was about 64%, regardless of the CO conversion in the WGS steps.
This result may be obtained by the mathematical relationships between the R-ratio, xWGS and αCO2. The captured carbon atoms were calculated as follows:
y C O 2 ( C O 2 , I N + C O I N   x W G S ) = 2   C O I N H 2 I N + 3   C O 2 , I N 3   ( C O 2 , I N + C O I N   x W G S ) ( C O 2 , I N + C O I N   x W G S ) = 2 3 C O I N 1 3 H 2 I N + C O 2 , I N
So, both xWGS and αCO2 do not affect the carbon capture level.

3.2. Economic Results

Four main sections were considered for the estimation of capital costs: (i) gasification and syngas cleaning; (ii) the water–gas shift; (iii) carbon capture and storage; and (iv) methanol synthesis.
Figure 5 shows the capital cost distribution as a function of the WGS conversion. Green bars represent the gasification and syngas cleaning section and it is equal to 27 M€, regardless of the WGS conversion level. On the contrary, WGS affects the capital costs of the WGS and CC sections, which have an opposite trend. To reach higher CO conversions, higher capital costs are estimated for the WGS section, while lower capital costs are estimated for the CC section; this thanks to higher partial pressures of the CO2 in the shifted syngas after favoring CO2 absorption during the Selexol® process. For low WGS conversions (i.e., 36–59%), the capital cost of the WGS section is below 6 M€ due to the absence of the LTS-WGS reactor. The highest value of the CC section is calculated for a 99% WGS conversion, with a value of 9.2 M€. On the other hand, the CC section is below 7 M€ for CO conversions in the range 70–99%, with the lowest value for CO conversion equal to 70% (i.e., 5.7 M€). The lowest capital costs of the CC section is calculated for a conversion of 70%, due to (i) a lower DEPG flowrate in the column, which requires a smaller column diameter; (ii) a smaller size pump at P2; and (iii) a lower amount of solvent to buy for the start-up of the absorption unit.
Globally, the combination of these effects leads to estimate that the minimum value of the capital costs at the point where xWGS = 70% is 42.8 M€. The most expensive case is for xWGS = 99%, at 46.3 M€.
Operating costs have a higher impact on the economic analysis. In fact, the lowest operating costs are for the case xWGS = 40% (13.1 M€/y) and the highest operating costs are for xWGS = 99%, at 13.8 M€/y, as shown in Figure 6.
Figure 6 shows the operating costs of the process as a function of the WGS conversion value. In particular, a constant cost is for the biomass supply (about 5.9 M€/y). The natural gas cost increases by increasing the CO conversion due to a higher H2O/CO ratio requested to obtain the desired conversion. This is the main effect of the H2O/CO ratio on the operating costs. A slighter effect is calculated in terms of electricity costs (2.7–2.9 M€/y). Maintenance and labor costs follow the same trend in capital costs since they were considered equal to 10% of the latter.
The effect of WGS conversion on methanol production cost is reported in Figure 7. The minimum production cost was calculated for a WGS conversion equal to 40%, with a value equal to 0.540 €/kg. The highest impact on the production cost were derived from the operating costs. Considering a 20-year plant life, the mean values of the annualized capital costs is equal to 2.2 M€/y, while the mean operating costs are about 13.4 M€/y. As shown in Figure 3, the natural gas demand increases with the H2O/CO ratio. The electricity demand for the case xWGS = 36% is 4% higher than electricity demand calculated for the optimal case, xWGS = 40%, due to the different electricity demanded by C5, which was caused by a lower V2 pressure. For a CO conversion between 49% and 80%, the methanol production cost is similar, which is about 0.545 €/kg, and depends on the natural gas demand.
For the WGS conversion of 90% and 99%, the natural gas cost is the main cause of higher production cost. For these cases, also the capital costs are higher than the case with a lower WGS conversion, due to the higher capital costs of both the WGS reactors (associated to CO conversion) and the ABS column due to a higher gas flowrate.
Obtained results may be affected by several variables, such as the syngas final pressure, which here was set to 80 bar. A higher pressure in the WGS section does not have an influence on the reaction equilibrium, but a higher partial pressure of the reactants would favor reaction kinetics, then requiring a smaller size of the reactors. Furthermore, the CC section is strongly affected by syngas pressure, because CO2 absorption would be more favored and, consequently, an optimal column size and solvent-to-gas ratio would be lower. On the other hand, the C1 compressor pressure also has an effect on the global economic analysis. In particular, in decreasing the C1 pressure, both the WGS reactor and CC section equipment size (column size, solvent flowrate) would be higher.
In the investigated process, since the optimal case was for a CO conversion equal to 40% and a CO2 capture equal to 95%, the optimal configuration was without an LTS-WGS reactor and both the H2O/CO and DEPG/GAS ratios equal to 1. In that case, operating costs were the lowest (13.1 M€/y), divided into 5.9 M€/y for biomass supply, 4.5 M€ for maintenance and labor, 2.8 M€/y for electricity and only 0.3 M€/y for the natural gas consumption. In particular, electricity consumption is required by the syngas compressor C1 (about 6.6 MWe), the CO2 compressor C5 (about 1.4 MWe) and by solvent pump P2 (about 0.66 MWe). Total capital costs were about 44.8 M€, as a sum of 27 M€ for the gasification system, 7.0 M€ for the compressors, 1.4 M€ for the pumps, 4.4 M€ for the Selexol® system and 1.1 M€ for the WGS. Compressor C1 was the most expensive compressor with a cost of 4.1 M€.
Finally, Figure 8 shows the annual cash flow for the optimal case. After the first two years for the plant construction (about −20 M€), revenues (higher than operating costs) make the annual cash flows positive, and at the 22nd year, the NPV is equal to zero. In the first years, cash flows are higher due to the effect of the discount rate (3%). For the last year, the working capital is recovered, making the cash flow equal to 0.9 M€/y.
Finally, considering the best production cost equal to 0.540 €/kg, it is comparable with the higher end of the cost range for pure hydrogen for Case A considered in Paragraph 2.1 [55]. For a price of pure hydrogen of 6 €/komlH2 [32], in fact, 0.449 €/kg is to purchase the pure hydrogen, not considering compression costs and capital costs of the gasifier and compressors.
The obtained results give insights in light of a growing development of a biorefinery concept, and confirm the production of methanol from biomass as a promising strategy to go towards a low-carbon society, although a more detailed study should be carried out [56,57,58,59,60,61,62,63]. For example, the methanol production costs strongly depend on plant capacity. In a recent paper, Wang et al. discussed the effect of feedstock and plant capacity on methanol production costs [64]. In particular, wood, waste, natural gas and coal were considered as raw materials for methanol synthesis. The methanol production cost strongly depends on the plant capacity, especially for the biomass-based processes.
By considering a cost analysis based on 2013 data, for plant capacities from a few tens to hundreds of kton/yr of methanol, the methanol production cost ranges from about 200 to 935 €/ton for either lignocellulose biomass (wood) or waste residues, from 160 to 480 €/ton for coal, and from 90 to 290 €/ton for natural gas. The production of methanol from fossils, especially in the case of natural gas, may be then considered the cheapest solution, although the cost of fossils may change as a function of several factors, such as geopolitics. Therefore, by considering our methanol production rate, namely about 35 kt/yr, our estimation (i.e., 540 €/ton) well agrees with the literature data.
In this work the management of the solid by-product of the gasification, the so-called char, was not considered. From the work of Barisano et al. [21], about 80–100 g of char are produced from 1 kg of dry biomass. If the biomass ash (1.2 wt%) is quantitatively preserved in the produced char, the organic fraction of the char is 88 wt%. The authors analyzed the organic fraction of char: a carbon content of 82 wt%, hydrogen content of about 4 wt% and 14 wt% oxygen [21]. On the basis of these analyses, the solid by-product of the gasification could be considered as biochar [65,66]. Biochar is a versatile product whose applications are continuously expanding, mainly in agriculture, operations related to the natural environment and industry. It can be used as a soil additive, or added to fodder and silage, or applied in water treatment. Biochar can also be used for the immobilization of contaminants from soil, and in sewage treatment; it can be applied as a supplementary material in composting and in methane fermentation processes. Biochar can be used as a catalyst for tar reduction in pyrolysis and gasification, and as a fuel when pelletized [66].

4. Conclusions

In this work, a techno-economic assessment of the upgrading of syngas from biomass gasification was studied. In particular, the WGS and CC sections were analyzed, varying the CO conversion in the WGS reactor and fixing to the optimal value, an R-ratio (H2CO2)/(CO + CO2) of 2. The relationship between CO conversion and percentage of CO2 to be removed was studied and the process parameters to obtain the same conditions of the syngas were found. For each case and process condition, an economic analysis was done and set equal to a zero net present value, thus finding the correspondent value of the production cost of methanol. The results show the convenience of lower CO conversions with respect to easier CO2 capturing processes. The main cost parameter is the H2O/CO ratio of the WGS section, due to the high natural gas cost. A CO conversion equals to 40% was calculated as the optimal value to obtain the lowest process cost with a methanol production cost of 0.540 €/kg.
More detailed studies should be carried out for a more accurate estimation of methanol production cost; but, on the whole, the obtained results reveal that an optimization of the upgrading system should be taken into account.

Author Contributions

Conceptualization: A.G.; methodology and computer-assisted simulations: A.G.; writing—original draft preparation and revision: A.G., C.F. and E.C. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Hasler, P.; Nussbaumer, T. Gas cleaning for IC engine applications from fixed bed biomass gasification. Biomass Bioenergy 1999, 16, 385–395. [Google Scholar] [CrossRef]
  2. Wu, C.; Huang, H.; Zheng, S.; Yin, X. An economic analysis of biomass gasification and power generation in China. Bioresour. Technol. 2002, 83, 65–70. [Google Scholar] [CrossRef]
  3. Zhou, Z.; Yin, X.; Xu, J.; Ma, L. The development situation of biomass gasification power generation in China. Energy Policy 2012, 51, 52–57. [Google Scholar] [CrossRef]
  4. De Bari, I.; Barisano, D.; Cardinale, M.; Matera, D.; Nanna, F.; Viggiano, D. Air Gasification of Biomass in a Downdraft Fixed Bed: A Comparative Study of the Inorganic and Organic Products Distribution. Energy Fuels 2000, 14, 889–898. [Google Scholar] [CrossRef]
  5. Available online: www.inerco.com (accessed on 11 May 2020).
  6. Olah, G.A. Beyond oil and gas: The Methanol Economy. Angew. Chem. Int. Ed. 2005, 44, 2636–2639. [Google Scholar] [CrossRef] [PubMed]
  7. Goeppert, A.; Olah, G.A.; Prakash, G.K.S. Towards a sustainable carbon cycle: The methanol economy. In Green Chemistry; Royal Society of Chemistry: London, UK, 2018; pp. 919–962. [Google Scholar]
  8. Migliori, M.; Catizzone, E.; Aloise, A.; Bonura, G.; Gómez-Hortigüela, L.; Frusteri, L.; Cannilla, C.; Frusteri, F.; Giordano, G. New insights about coke deposition in methanol-to-DME reaction over MOR-, MFI-, and FER-type zeolites. J. Ind. Eng. Chem. 2018, 68, 196–208. [Google Scholar] [CrossRef]
  9. Keil, F.J. Methanol-to-hydrocarbons: Process technology. Microp. Mesop. Mater. 1999, 29, 49–66. [Google Scholar] [CrossRef]
  10. Catizzone, E.; Cirelli, Z.; Aloise, A.; Lanzafame, P.; Migliori, M.; Giordano, G. Methanol conversion over ZSM-12, ZSM-22 and EU-1 zeolites: From DME to hydrocarbons production. Catal. Today 2018, 304, 39–50. [Google Scholar] [CrossRef]
  11. Tian, P.; Wei, Y.; Ye, M.; Liu, Z. Methanol to Olefins (MTO): From Fundamentals to Commercialization. ACS Catal. 2015, 5, 1922–1938. [Google Scholar] [CrossRef]
  12. Galadima, A.; Muraza, O. From synthesis gas production to methanol synthesis and potential upgrade to gasoline range hydrocarbons: A review. J. Nat. Gas Sci. Eng. 2015, 25, 303–316. [Google Scholar] [CrossRef]
  13. Torres, W.; Pansare, S.S.; Goodwin, J.G. Hot Gas Removal of Tars, Ammonia, and Hydrogen Sulfide from Biomass Gasification Gas. Catal. Rev. 2007, 49, 407–456. [Google Scholar] [CrossRef]
  14. Guan, G.; Keawpanha, M.; Hao, X.; Abudula, A. Catalytic steam reforming of biomass tar: Prospects and challenges. Renew. Sustain. Energy Rev. 2016, 58, 450–461. [Google Scholar] [CrossRef] [Green Version]
  15. Giuliano, A.; Catizzone, E.; Freda, C.; Cornacchia, G. Valorization of OFMSW Digestate-Derived Syngas toward Methanol, Hydrogen, or Electricity: Process Simulation and Carbon Footprint Calculation. Processes 2020, 8, 526. [Google Scholar] [CrossRef]
  16. McCaffrey, Z.; Thy, P.; Long, M.; Oliveira, M.; Wang, L.; Torres, L.; Aktas, T.; Chiou, B.; Orts, W.; Jenkins, B.M. Air and Steam Gasification of Almond Biomass. Front. Energy Res. 2019, 7, 84. [Google Scholar] [CrossRef]
  17. Campoy, M.; Gòmez-Barea, A.; Villanueva, A.L.; Ollero, P. Air-Steam Gasification of Biomass in a Fluidized Bed under Simulated Autothermal and Adiabatic Conditions. Ind. Eng. Chem. Res. 2008, 47, 5957–5965. [Google Scholar] [CrossRef]
  18. Belaissaoui, B.; Le Moullec, Y.; Hagi, H.; Favre, E. Energy Efficiency of Oxygen Enriched Air Production Technologies: Cryogeny vs. Membranes. Energy Procedia 2014, 63, 497–503. [Google Scholar] [CrossRef] [Green Version]
  19. Smith, A.R.; Klosek, J. A review of air separation technologies and their integration with energy conversion processes. Fuel Process. Technol. 2011, 70, 115–134. [Google Scholar] [CrossRef]
  20. Meng, X.; de Jong, W.; Fu, N.; Verkooijen, A.H.M. Biomass gasification in a 100 kWth steam-oxygen blown circulating fluidized bed gasifier: Effects of operational conditions on product gas distribution and tar formation. Biomass Bioenergy 2011, 35, 2910–2924. [Google Scholar] [CrossRef]
  21. Barisano, D.; Canneto, G.; Nanna, F.; Braccio, G. Steam/oxygen biomass gasification at pilot scale in an internally circulating bubbling fluidized bed reactor. Fuel Process. Technol. 2016, 141, 74–81. [Google Scholar] [CrossRef]
  22. Pfeifer, C.; Koppatz, S.; Hofbauer, H. Steam gasification of various feedstocks at a dual fluidised bed gasifier: Impacts of operation conditions and bed materials. Biomass Conv. Bioref. 2011, 11, 39–53. [Google Scholar] [CrossRef]
  23. Catizzone, E.; Bonura, G.; Migliori, M.; Frusteri, F.; Giordano, G. CO2 recycling to dimethyl ether: State-of-the-art and perspectives. Molecules 2018, 23, 31. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  24. Bonura, G.; Cannilla, C.; Frusteri, L.; Catizzone, E.; Todaro, S.; Migliori, M.; Giordano, G.; Frusteri, F. Interaction effects between CuO-ZnO-ZrO2 methanol phase and zeolite surface affecting stability of hybrid systems during one-step CO2 hydrogenation to DME. Catal. Today 2020, 345, 175–182. [Google Scholar] [CrossRef]
  25. Macrì, D.; Catizzone, E.; Molino, A.; Migliori, M. Supercritical waster gasification of biomass and agro-food residues: Energy assessment from modelling approach. Renew. Energy 2020, 150, 624–636. [Google Scholar] [CrossRef]
  26. Iaquaniello, G.; Centi, G.; Salladini, A.; Palo, E.; Spadacini, L. Waste-to-methanol: Process and economics assessment. Biores. Technol. 2017, 243, 611–619. [Google Scholar] [CrossRef] [PubMed]
  27. Perathoner, S.; Centi, G. CO2 recycling: A key strategy to introduce green energy in the chemical production chain. ChemSusChem 2014, 7, 1274–1282. [Google Scholar] [CrossRef]
  28. Feng, W.; Ji, P.; Chen, B.; Zheng, D. Analysis of methanol production from biomass gasification. Chem. Eng. Technol. 2011, 34, 307–317. [Google Scholar] [CrossRef]
  29. Puig-Gamero, M.; Argudo-Santamaria, J.; Valverde, J.L.; Sànchez, P.; Sanchez-Silva, L. Three integrated process simulation using aspen plus: Pine gasification, syngas cleaning and methanol synthesis. Energy Conv. Manag. 2018, 177, 416–427. [Google Scholar] [CrossRef]
  30. LeValley, T.L.; Richard, A.R.; Fan, M. The progress in water gas shift and steam reforming hydrogen production technologies—A review. Int. J. Hydrogen Energy 2014, 39, 16983–17000. [Google Scholar] [CrossRef]
  31. Ju, F.; Chen, H.; Ding, X.; Yang, H.; Wang, X.; Zhang, S.; Dai, Z. Process simulation of single-step dimethyl ether production via biomass gasification. Biotechnol. Adv. 2009, 27, 599–605. [Google Scholar] [CrossRef]
  32. Robinson, P.J.; Luyben, W.L. Integrated Gasification Combined Cycle Dynamic Model: H2S Absorption/Stripping, Water-Gas Shift Reactors, and CO2 Absorption/Stripping. Ind. Eng. Chem. Res. 2010, 49, 4766–4781. [Google Scholar] [CrossRef]
  33. Giuliano, A.; Poletto, M.; Barletta, D. Pure hydrogen co-production by membrane technology in an IGCC power plant with carbon capture. Int. J. Hydrogen Energy 2018, 43, 19279–19292. [Google Scholar] [CrossRef]
  34. Chiodini, A.; Bua, L.; Carnelli, L.; Zwart, R.; Vreugdenhil, B.; Vocciante, M. Enhancements in Biomass-to- Liquid processes: Gasification aiming at high hydrogen/carbon monoxide ratios for direct Fischer-Tropsch synthesis applications. Biomass Bioenergy 2017, 106, 104–114. [Google Scholar] [CrossRef]
  35. Giuliano, A.; Catizzone, E.; Barisano, D.; Nanna, F.; Villone, A.; De Bari, I. Towards Methanol Economy: A Techno-environmental Assessment for a Bio-methanol OFMSW/Biomass/Carbon Capture-based Integrated Plant. Int. J. Heat. Technol. 2019, 37, 665–674. [Google Scholar] [CrossRef]
  36. Dinca, C.; Slavu, N.; Cormoş, C.C.; Badea, A. CO2 capture from syngas generated by a biomass gasification power plant with chemical absorption process. Energy 2018, 149, 925–936. [Google Scholar] [CrossRef]
  37. Centi, G.; Perathoner, S. Towards solar fuels from water and CO2. ChemSusChem 2010, 3, 195–208. [Google Scholar] [CrossRef] [PubMed]
  38. Gazzani, M.; MacChi, E.; Manzolini, G. CO2 capture in integrated gasification combined cycle with SEWGS—Part A: Thermodynamic performances. Fuel 2013, 5, 206–219. [Google Scholar] [CrossRef]
  39. Yang, Q.; Li, X.; Yang, Q.; Huang, W.; Yu, P.; Zhang, D. Opportunities for CO2 Utilization in Coal to Green Fuel Process: Optimal Design and Performance Evaluation. ACS Sustain. Chem. Eng. 2020, 8, 1329–1342. [Google Scholar] [CrossRef]
  40. Khanipour, M.; Mirvakili, A.; Bakhtyari, A.; Farniaei, M.; Rahimpour, M.R. A membrane-assisted hydrogen and carbon oxides separation from flare gas and recovery to a commercial methanol reactor. Int. J. Hydrogen Energy 2020, 45, 7386–7400. [Google Scholar] [CrossRef]
  41. Hla, S.S.; Park, D.; Duffy, G.J.; Edwards, J.H.; Roberts, D.G.; Ilyushechkin, A. Kinetics of high-temperature water-gas shift reaction over two iron-based commercial catalysts using simulated coal-derived syngases. Chem. Eng. J. 2009, 146, 148–154. [Google Scholar] [CrossRef]
  42. Bozzano, G.; Manenti, F. Efficient methanol synthesis: Perspectives, technologies and optimization strategies. Prog. Energy Combust. Sci. 2016, 56, 71–105. [Google Scholar] [CrossRef]
  43. Choi, Y.; Stenger, H.G. Water gas shift reaction kinetics and reactor modeling for fuel cell grade hydrogen. J. Power Sources 2003, 124, 432–439. [Google Scholar] [CrossRef]
  44. Sofia, D.; Giuliano, A.; Poletto, M.; Barletta, D. Techno-economic analysis of power and hydrogen coproduction by an IGCC plant with CO2 capture based on membrane technology. Comp. Aided Chem. Eng. 2015, 37, 1373–1378. [Google Scholar]
  45. Sandler, S.I. Chemical, Biochemical, and Engineering Themodynamcs, 4th ed.; Wiley: Hoboken, NJ, USA, 2017. [Google Scholar]
  46. Menin, L.; Vakalis, S.; Benedetti, V.; Patuzzi, F.; Baratieri, M. Techno-economic assessment of an integrated biomass gasification, electrolysis, and syngas biomethanation process. Biomass Conv. Bioref. 2020, 1–15. [Google Scholar] [CrossRef]
  47. Giuliano, A.; Poletto, M.; Barletta, D. Process Design of a Multi-Product Lignocellulosic Biorefinery. Comput. Aided Chem. Eng. 2015, 37, 1313–1318. [Google Scholar]
  48. Dorris, C.C.; Lu, E.; Park, S.; Toro, F.H. High-Purity Oxygen Production Using Mixed Ionic-Electronic Conducting Sorbents. Penn Engineering. Available online: http://repository.upenn.edu/cbe_sdr/78 (accessed on 30 June 2020).
  49. Seider, W.D.; Lewin, D.R.; Seader, D.J.; Widagdo, S.; Gani, R.; Ng, K.M. Product and Process Design Principles: Synthesis, Analysis and Evaluation, 4th ed.; Wiley: New York, NY, USA, 2016. [Google Scholar]
  50. Giuliano, A.; Barletta, D.; De Bari, I.; Poletto, M. Techno-economic assessment of a lignocellulosic biorefinery co-producing ethanol and xylitol or furfural. Comput. Aided Chem. Eng. 2018, 43, 585–590. [Google Scholar]
  51. Giuliano, A.; Cerulli, R.; Poletto, M.; Raiconi, G.; Barletta, D. Process Pathways Optimization for a Lignocellulosic Biorefinery Producing Levulinic Acid, Succinic Acid, and Ethanol. Ind. Eng. Chem. Res. 2016, 55, 10699–10717. [Google Scholar] [CrossRef]
  52. Hamelinck, C.N.; Van Hooijdonk, G.; Faaij, A.P. Ethanol from lignocellulosic biomass: Techno-economic performance in short-, middle- and long-term. Biomass Bioenergy 2005, 28, 384–410. [Google Scholar] [CrossRef]
  53. Leonzio, G. Methanol Synthesis: Optimal Solution for a Better Efficiency of the Process. Processes 2018, 6, 20. [Google Scholar] [CrossRef] [Green Version]
  54. Hamelinck, C.N.; Faaij, A.P.C. Future prospects for production of methanol and hydrogen from biomass. J. Power Source 2002, 111, 1–22. [Google Scholar] [CrossRef]
  55. Pérez-Arteaga, L.E.; Gómez-Cápiro, O.; Karelovic, A.; Jiménez, R. A modelling apporach to the techno-economics of biomass-to-DNG/Methanol systems: Standalone vs integrated topologies. Chem. Eng. J. 2016, 286, 663–678. [Google Scholar] [CrossRef]
  56. Calabrò, P.S.; Fazzino, F.; Folino, A.; Paone, E.; Komilis, D. Semi-continuous anaerobic digestion of orange peel waste: Effect of activated carbon addition and alkaline pretreatment on the process. Sustainability 2019, 11, 3386. [Google Scholar] [CrossRef] [Green Version]
  57. Fasolini, A.; Cucciniello, R.; Paone, E.; Mauriello, F.; Tabanelli, T. A Short Overview on the Hydrogen Production Via Aqueous Phase Reforming (APR) of Cellulose, C6-C5 Sugars and Polyols. Catalysts 2019, 9, 917. [Google Scholar] [CrossRef] [Green Version]
  58. Paone, E.; Tabanelli, T.; Mauriello, F. The rise of lignin biorefinery. Curr. Opin. Green Sustain. Chem. 2020, 24, 1–6. [Google Scholar] [CrossRef]
  59. Cherubini, F. The Biorefinery concept: Using biomass instead of oil for producing energy and chemicals. Energy Conv. Manag. 2010, 51, 1412–1421. [Google Scholar] [CrossRef]
  60. Menon, V.; Rao, M. Trends in bioconversion of lignocellulose: Biofuels, platform chemicals and Biorefinery concept. Progress Energy Comb. Sci. 2012, 38, 522–550. [Google Scholar] [CrossRef]
  61. Zhang, H.; Wang, L.; Pérez-Fortes, M.; Van herle, J.; Maréchal, F.; Desideri, U. Techno-economic optimization of biomass-to-methanol with solid-oxide electrolyze. Appl. Energy 2020, 258, 114071. [Google Scholar] [CrossRef]
  62. Kumabe, K.; Fujimoto, S.; Yanagida, T.; Ogata, M.; Fukuda, T.; Yabe, A.; Minowa, T. Environmental and economic analysis of methanol production process via biomass gasification. Fuel 2008, 87, 1422–1427. [Google Scholar] [CrossRef]
  63. Michailos, S.; Parker, D.; Webb, C. A multicriteria comparison of utilizing sugar cane bagasse for methanol to gasoline and butanol production. Biomass Bioenergy 2016, 95, 436–448. [Google Scholar] [CrossRef]
  64. Wang, S.-W.; Li, D.-X.; Ruan, W.-B.; Jin, C.-L.; Farahani, M.R. A techno-economic review of biomass gasification for production of chemicals. Energy Sources Econ. Plan. Policy 2018, 13, 351–356. [Google Scholar] [CrossRef]
  65. Available online: https://phyllis.nl/Browse/Standard/ECN-Phyllis (accessed on 30 June 2020).
  66. Saletnik, B.; Zaguła, G.; Bajcar, M.; Tarapatskyy, M.; Bobula, G.; Puchalski, C. Biochar as a Multifunctional Component of the Environment—A Review. Appl. Sci. 2019, 9, 1139. [Google Scholar] [CrossRef] [Green Version]
Figure 1. Calculated CO2 removal rate as a function of CO conversion in the water–gas shift (WGS) to obtain an R = 2.
Figure 1. Calculated CO2 removal rate as a function of CO conversion in the water–gas shift (WGS) to obtain an R = 2.
Bioengineering 07 00070 g001
Figure 2. The syngas-to-methanol production flowsheet considered in this work.
Figure 2. The syngas-to-methanol production flowsheet considered in this work.
Bioengineering 07 00070 g002
Figure 3. Natural gas and electricity required as function of CO conversion in the WGS step.
Figure 3. Natural gas and electricity required as function of CO conversion in the WGS step.
Bioengineering 07 00070 g003
Figure 4. The effect of CO conversion in the WGS step on the CO2 content (left axes) and low heat value (right axes) of the post-CCS, upgraded syngas.
Figure 4. The effect of CO conversion in the WGS step on the CO2 content (left axes) and low heat value (right axes) of the post-CCS, upgraded syngas.
Bioengineering 07 00070 g004
Figure 5. Capital costs as a function of WGS conversion. Gasification includes syngas cleaning.
Figure 5. Capital costs as a function of WGS conversion. Gasification includes syngas cleaning.
Bioengineering 07 00070 g005
Figure 6. Operating costs varying with the WGS conversion.
Figure 6. Operating costs varying with the WGS conversion.
Bioengineering 07 00070 g006
Figure 7. Cost of the upgraded syngas for methanol synthesis expressed in kmol of carbon atoms.
Figure 7. Cost of the upgraded syngas for methanol synthesis expressed in kmol of carbon atoms.
Bioengineering 07 00070 g007
Figure 8. Annual cash flow for the optimal WGS conversion (xWGS = 40%).
Figure 8. Annual cash flow for the optimal WGS conversion (xWGS = 40%).
Bioengineering 07 00070 g008
Table 1. The syngas composition considered in this work (average values of the data reported in [21]).
Table 1. The syngas composition considered in this work (average values of the data reported in [21]).
COH2CO2CH4N2
303025105
Table 2. Process equipment of the considered flowsheet of Figure 2.
Table 2. Process equipment of the considered flowsheet of Figure 2.
SectionEquipmentEquipment KindUtility or Steam Required/Produced
WGSC1CompressorElectricity
WGSE1Heat exchangerNatural gas
WGSE2Heat exchangerLPS produced
WGSP1PumpElectricity
WGSHTS-WGSReactor/
WGSE3Heat exchangerLPS produced
WGSLTS-WGSReactor/
WGSE4Heat exchangerCooling water
WGSF1Condenser/
CCSC2CompressorElectricity
CCSE5Heat exchangerCooling water
CCSABSAbsorption column/
CCSE8Heat exchangerLPS required
CCSV1Valve/
CCSE6Heat exchangerLPS required
CCSF2Flash/
CCSC3CompressorElectricity
CCSV2Valve/
CCSE7Heat exchangerLPS required
CCSF3Flash/
CCSC5CompressorElectricity
CCSP2PumpElectricity
CCSC4CompressorElectricity
Table 3. Process variables description.
Table 3. Process variables description.
SectionProcess VariableUnitsRangeEffect
WGSH2O/CO-1–3WGS Conversion
WGSWGS-HTS lengthm0–2WGS Conversion/ WGS-HTS Pressure drop
WGSWGS-LTS lengthm0–5WGS Conversion/ WGS-LTS Pressure drop
CCSDEPG/GAS-0.5–1CO2 absorption
CCSV1 output pressurebar10–70CO2 absorption/ Captured CO2 purity
CCSV2 output pressurebar0.7–2CO2 absorption/ Captured CO2 purity
Table 4. Economic parameters used in the economic analysis.
Table 4. Economic parameters used in the economic analysis.
Economic ParameterUnitsCalculationValueReference
Biomass supply chain cost (CB)€/t 40[47]
Oxygen purchase cost€/t 40[48]
LPS€/t 7[49]
MPS€/t 11[49]
Natural gas€/Nm3 0.136[49]
DEPG cost€/t 5000[32]
Column packing€/m3 1000[32]
Electricity€/MWh 40-
Column stage heightM 0.5[32]
ABS stage- 12[32]
Working hour per yearh/y 7920[32]
Fp 0.5/7/50 bar1/1.5/1.9[49]
Ft 100/300/500 °C1/1.6/2.1[49]
Construction yearsY 2-
Depreciation years (yD)Y 20[50]
Maintenance and labor (OCM)M€/y% of total capital cost10[51]
Working capital (WC)M€ % of total capital cost2[32]
Taxes (t)%of the gross profit40[32]
Discount rate (r)% 3-
Table 5. Final variable values.
Table 5. Final variable values.
WGS Conversion (%)Removed CO2 (%)H2O/CODEPG/GASV1/V2 Pressure (bar)
36981125/0.7
40951120/1.6
498820.721/1.3
598220.719/1.5
707620.558/0.7
807220.528/0.7
906730.527/1.5
996430.523/1.1

Share and Cite

MDPI and ACS Style

Giuliano, A.; Freda, C.; Catizzone, E. Techno-Economic Assessment of Bio-Syngas Production for Methanol Synthesis: A Focus on the Water–Gas Shift and Carbon Capture Sections. Bioengineering 2020, 7, 70. https://doi.org/10.3390/bioengineering7030070

AMA Style

Giuliano A, Freda C, Catizzone E. Techno-Economic Assessment of Bio-Syngas Production for Methanol Synthesis: A Focus on the Water–Gas Shift and Carbon Capture Sections. Bioengineering. 2020; 7(3):70. https://doi.org/10.3390/bioengineering7030070

Chicago/Turabian Style

Giuliano, Aristide, Cesare Freda, and Enrico Catizzone. 2020. "Techno-Economic Assessment of Bio-Syngas Production for Methanol Synthesis: A Focus on the Water–Gas Shift and Carbon Capture Sections" Bioengineering 7, no. 3: 70. https://doi.org/10.3390/bioengineering7030070

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop